|
Stile & Rail
STANDARD MANUFACTURING CONSTRUCTION DETAILS
- 3" Stile & Rail Construction
- 14 Guage Stainless Steel
- Type 304
- Type 316
- Finish #4 Satin
- Vertical Grain
- Seamless Edges
- Welded, Ground and Polished Joints
- Prepared for Deadbolt
- Reinforced Hinges
- Reinforced for Push/Pull
-
- Spec Sheet
back to top
Steel Stiffened
STANDARD MANUFACTURING CONSTRUCTION DETAILS
- Flush Door
- 16 Guage Stainless Steel
- Type 304
- Type 316
- Finish #4 Satin
- Vertical Grain
- Edge Seam (lockseam) or Optional No Edge Seam (seamless)
- Vertical Hat Stiffeners 6" on Center
- Insulation Between Stiffners
- Hinge Reinforcements 3/16" by 1 1/4" by 10" long for 4 1/2" Standard Weight Hinges
- Lock Reinforcement Box - 14 gauge with Tabs
- Inverted Top and Bottom Channels - 18 gauge
- Surface Applied Closer Reinforcement - 12 gauge
- Prepared for ANSI 161 Cylinder Lock
- Inverted Top and Bottom Channels - 18 gauge
-
- Spec Sheet
back to top
Seamless Doors
STANDARD MANUFACTURING CONSTRUCTION DETAILS
- Flush Door
- 16 Guage Stainless Steel
- Type 304
- Type 316
- Finish #4 Satin
- Vertical Grain
- NO Edge Seam (seamless edge)
- Polystyrene Core
- Hinge Reinforcements 3/16" by 1 1/4" by 10" long for 4 1/2" Standard Weight Hinges
- Lock Reinforcement Box - 14 gauge with Tabs
- Inverted Top and Bottom Channels - 18 gauge
- Surface Applied Closer Reinforcement - 12 gauge
- Prepared for ANSI 161 Cylinder Lock
-
- Spec Sheet
back to top
Seamed Doors
STANDARD MANUFACTURING CONSTRUCTION DETAILS
- Flush Door
- 16 Guage Stainless Steel
- Type 304
- Type 316
- Finish #4 Satin
- Vertical Grain
- Edge Seam (lockseam)
- Polystyrene Core
- Hinge Reinforcements 3/16" by 1 1/4" by 10" long for 4 1/2" Standard Weight Hinges
- Lock Reinforcement Box - 14 gauge with Tabs
- Inverted Top and Bottom Channels - 18 gauge
- Surface Applied Closer Reinforcement - 12 gauge
- Prepared for ANSI 161 Cylinder Lock
-
- Spec Sheet
back to top
Fire Rated Steel Doors
Stainless Doors, Inc., upon completing testing, was awarded listing for singles to 4/0 by 8/0 and pairs 8/0 by 8/0 using 300 series stainless steel. With optional lites, louvers, swing hardware and fire device configurations, SDI doors can meet your most critical environmental requirements. Contact the factory for listing specifications.
 Spec Sheet
back to top
Fire Rated Steel Stiffened Stainless Steel Doors
Stainless Doors, Inc. has received fire approval for a steel stiffened design without any marks on the door skins. With the stiffener channels welded together to the top and bottom door channels and door face skins, our engineers have created an integral frame structure that leaves no visible marks or distortions on the door face skins. This innovative design improves the strength and durability of a steel stiffened door.
Spec Sheet
back to top
Fire Rated Stainless Steel Frames
SDI frames have been tested and approved in 16, 14, and 12 gauge series 300 stainless steel. Our frame assemblies for swinging fire doors encompasses a wide range of sizes, including multiple anchoring methods. Contact the factory for listing specifications.
Spec Sheet
back to top
Door Cores
Spec Sheet
Honeycomb
-
U-Factor = .42
-
R-Factor = 2.4
Polystyrene
-
U-Factor = .13
-
R-Factor = 7.7
Polyurethane
-
U-Factor = .08
-
R-Factor = 12.0
Steel Stiffened
U and R-Factors depend upon insulation, mineral wool, ceramic wool, or fiberglass.
back to top
FRAMES
STANDARD MANUFACTURING CONSTRUCTION DETAILS
- Three Sided Frame
- 16 Guage Stainless Steel
- Type 304
- Type 316
- Finish #4 Satin
- Vertical Grain
- Mitered and Welded Faces
- Hinge Reinforcements 3/16" by 1 1/4" by 10" long for 4 1/2" Standard
- Weight Hinges
- Strike Reinforcement Tabs 12 gauge
- Prepared for ANSI Strike
- Prepared to receive 3 Door Silencers
- Each Jamb has Fixed Floor Anchor Clips
- Provided with Jamb Anchors
- Up to 6" Standard Jamb Depth
- 2" Standard Faces on Jambs and Head
-
- Spec Sheet
back to top
ACCESSORIES
Anchor Systems
Fixed Floor Clip
Masonry Loose "T"
Steel Stud
Wood Stud
Adjustable Masonry
EMA Pierce & Dimple
Concealed EMA With Caps
Spec Sheet
Reinforcements
Hinge Reinforcement 1- 1/4¨ wide x 10¨ long x 3/16¨ thick
Hinge Reinforcement with Dust Cover
Strike Reinforcement with Dust Cover
12 Gauge Strike Reinforcement
12 Gauge Reinforcement on Soffit or Rabbets for Various Hardware Configurations either on Jambs or Head
Spec Sheet
Glazing Trim
STANDARD MANUFACTURING CONSTRUCTION DETAILS
- Opening Support Channel 18 gauge
- 18 gauge Stainless Steel Channel Stops
- Type 304
- Type 316
- Finish #4 Satin
- Vertical Grain
- Glazing Thickness from 1/4" to 1"
- Removable Trim Frames with Square Corners
- Mitered and Tacked
- Truss Head Mounting Screws Supplied
-
- Spec Sheet
back to top |
